| MICROPROCESSOR BASED INFRARED GAS ANALYZER Model ZRH (Single or Dual Component) |
DESCRIPTION
The Model ZRH is a single or dual component non-dispersive infrared (NDIR) gas
analyzer used for measuring CO, CO2, CH4, and SO2. It (Insert) achieves high
accuracy and provides multiple function and ease of operation through the use
of a microprocessor. It is available in 19-inch rack, panel or tabletop mountings.
Zero and span calibrations are easily accomplished by pressing the appropriate
key on the front panel.
The ZRH has an improved single beam optical system, which provides superior
performance to conventional double beam analyzers. It is easy to maintain and
offers excellent long-term stability. The ZRH is ideal for continuous measurement
in the combustion control of burners, incinerators and furnaces as well as CEM-stack
systems. The dual cell type of transmission detector minimizes interferences
from other gas components from other gas components.
The ZRH optical design and modular construction assures long term reliability.
| FEATURES • Microprocessor controlled • Single source, single beam optics • Direct readout in engineering units • Linear output • Low sensitivity to vibration • 1 or 2 components, multiple ranges • Self diagnosis function • No optical alignment required • RS-232C interface • Easy maintenance • 19" rack mountable |
OPTIONS • Auto calibration • Remote range change and range identification output • Barometric pressure compensation |
APPLICATIONS • Combustion efficiency: • Boilers, incinerators & furnaces (CO, CO2, SO2) • Commercial ovens (CO, CO2) • Controlled atmospheres: • Heat treating (CO, CO2, CH4) • Greenhouses (CO2) • Fermentation (CO2) • Air liquification (CO2) • Landfill emissions (CO2, CH4) • Process chemical gas analysis • Respiration studies: • Single breath lung diffusion (CO) • Stack gases: CEM (CO, CO2, SO2) • Vehicle emissions |
| SPECIFICATIONS
MEASURABLE GAS COMPONENTS: Single component, multiple range analyzer: CO2, CO, CH4, and SO2 Two-component multiple range analyzer: Any two ranges: Up to 3 ranges (optional) 200 ppm to 100% Range- maximum 5 to 1 MEASURING SYSTEM: Nondispersive infrared absorption (NDIR) method, singe light source-single beam OUTPUTS: Analog 4 to 20mA DC, and 0 to 1mV or 0 to 1V or 0 to 5V or 0 to 10VDC selectable RS-232C REPEATABILITY: 1st range (low range): Within ± 0.5% of full scale 2nd range (high range): Within ± 1% of full scale ZERO DRIFT: Within ± 1% of full scale/24 hrs SPAN DRIFT: Within ± 1% of full scale/24 hrs RESPONSE TIME: Within 3 seconds, depending on cell length and flow rate LINEARITY: ± 1% of full scale NOISE: ± 0.5% of full scale POWER SUPPLY: 100, 115, 200 (± 10%) VAC, 50/60 Hz POWER CONSUMPTION: 37VA max. AMBIENT TEMPERATURE: 23-113° F (-5 to +45° C) AMBIENT HUMIDITY: Less than 90% RH non-condensing ENCLOSURE: Steel casing, for indoor use DISPLAY: 4 digit LED for concentration display; 4 digit LED for sub-display OUTPUT HOLD: Output value can be held during manual or automatic calibration function MEASURED GAS TEMPERATURE: 32-122° F (0 to 50° C) 20-50° C for water vapor applications WARM-UP TIME: Approximately 1 hour GAS INLET/OUTLET, PURGE GAS INLET SIZE: NPT ¼" internal thread MEASURED GAS FLOW RATE: 0.5 to 2 liters/min. PURGE GAS FLOW RATE: 1 liter/min. DIMENSIONS: Rack Mount: 5 ¼" H x 19" W x 17 ½" D (133mm x 483mm x 448mm) Panel Mount: 5 ¼" H x 17 ½" W x 17 ½" D (133mm x 443mm x 448mm) Table Top: 5 ¾" H x 17 ½" W x 17 ½" D (145mm x 443mm x 448mm) WEIGHT: Approximately 27lbs. (12 kg) Specifications subject to change without notice |
||
back to infrared gas analyzers
home
sitemap
EAS service
links
testimonials
Environmental
Analytical Systems
286 Mask Island Drive
Barry's Bay, Ontario, Canada K0J 1B0
Phone:
613 756 0101
Toll Free (Canada only):
1 800 427 8591
Fax: 613 756 0909
email: info@enviro-analytical.com
©Environmental Analytical Systems 2003
